A Designers' Guide to Batteries for Portable and Wearable Devices

By John Dring, VP of Engineering, Voler Systems

John Dring, VP of Engineering, Voler Systems

Our clients usually want the batteries in their products to be extremely small, to generate plenty of power, and to last forever. However, no existing batteries can meet all of these criteria and unfortunately, battery technology does not change very fast. Maybe things will get a little better; battery capacities do tend to increase over time with incremental improvements and new battery chemistries sometimes replace older ones. Moore’s Law does not and never did apply to batteries.

Almost all of the things that we can do to extend battery life in portable and wearable device design have less to do with the batteries and a lot with the electronics. You can use microprocessors and microcontrollers that draw less power or can push most of the high-power processing from the device to the cloud.

There are currently several alternative battery technologies and chemistries available for new designs. Older battery chemistries such as NiCd and NiMH have been supplanted by newer chemistries that offer better energy density and other advantages. Lead-acid batteries are simply too heavy for portable and wearable devices..

When selecting a battery for a portable or wearable system, there are two fundamental alternatives: primary cells and batteries and rechargeable cells and batteries. Primary cells cannot be recharged. They are designed for one-time use. Available primary cells commonly used for portable and wearable devices today include alkaline batteries, lithium manganese dioxide (coin) cells, and zinc-air cells. The leading rechargeable battery alternative is the lithium-polymer battery, which has replaced metal and plastic-clad lithium-ion batteries, largely because of more versatility.

Primary, One-Time-Use Batteries

Here are some key characteristics of primary batteries and cells currently used for portable and wearable applications:

• Alkaline cells have been available for a long time. The modern alkaline dry battery is based on zinc/manganese-dioxide chemistry, and comes in many standard sizes, which makes them very convenient for use in portable devices. In addition, alkaline cells are inexpensive, have good energy density, and can deliver high peak currents. However, alkaline cells are larger and heavier than other alternatives and are therefore make them good for portable designs but not for wearable devices.

• Lithium manganese dioxide cells—also called watch batteries, coin cells, and button cells—are another common type of primary cell. Small devices such as wrist watches, pocket calculators, cardiac pacemakers and defibrillators, and keyless entry transmitters for cars (key fobs) are usually powered by coin cells. Lithium manganese dioxide cells have a decent amount of capacity for their size but they also have a problem.

Although lithium manganese dioxide battery capacity as rated in milliamp hours can be pretty reasonable, these batteries exhibit a problem with respect to peak power draw. You cannot draw a lot of power from these cells over a short period of time. If you try to draw too much power from these cells too quickly, they degrade and will not recover. High current draws drain these cells disproportionately faster than lower current draws.

• Zinc-air batteries are another type of coin cell with somewhat better energy density than lithium manganese dioxide cells. Unlike most other primary cells that are self-contained, zinc-air cells generate electricity through a metal-air chemical reaction that oxidizes powdered zinc using oxygen from the atmosphere. Zinc-air batteries are commonly used as primary cells in hearing aids, so they are easily found at local pharmacies, which makes them good candidates for use in portable and wearable devices.

"Almost all of the things that we can do to extend battery life in portable and wearable device design have less to do with the batteries and a lot with the electronics"

Zinc-air batteries have very good energy density relative to lithium manganese dioxide batteries because the oxygen used for the chemical reaction is not built into the battery; it is harvested from the Earth’s atmosphere. In addition, zinc-air batteries do not have the peak-power-draw issue that lithium manganese dioxide batteries have. The downside to using zinc-air batteries is that they require access to the atmosphere, which presents a significant mechanical design challenge while developing a waterproof device.

Rechargeable Batteries

Lithium-ion polymer batteries, usually called lithium polymer batteries or LiPo batteries for short, have largely displaced other rechargeable batteries formerly used to power portable and wearable devices. These older battery chemistries included NiCd, NiMH, and metal-cased lithium ion batteries. LiPo batteries have replaced these other batteries because they are lighter in weight and have high energy density with low internal electrical leakage, so they will hold an electrical charge for a long time while a portable or wearable device is dormant or in storage.

If one of the myriad standard LiPo battery sizes and shapes will not work for a particular system design, it is possible to have a custom-designed battery made, even in prototype quantities as long as you are willing to pay the non-recurring engineering charges.

Most LiPo batteries are packaged in somewhat flexible yet fragile metalized foil bags instead of the rigid, metal cases used to package most other batteries. As a result, the product design’s battery compartment that houses the LiPo batteries takes more design consideration. The compartment must ensure that the battery is not exposed to anything that might pierce or physically damage the battery while accommodating the battery swell.

Use Battery Management System Boards for Safety

Spectacular news accounts of lithium batteries overheating and catching fire in portable applications such as laptop computers, hover boards, and mobile phones underscore the need to carefully manage the charging and discharging of all lithium batteries. These spectacular fires are a direct result of lithium batteries’ high energy density being discharged far too rapidly due to some design error or a mechanical or electrical fault.

Consequently, we always advocate the use of a BMS (battery management system) board for safety, which is directly incorporated into the packaged battery to prevent the LiPo battery from operating outside the safe zone, and balance the cells in multi-cell LiPo batteries during charging. These inexpensive safety circuits excel at detecting battery charging and discharging problems, and shut the systems down in case of overcharging or short-circuit loads.

In our designs using LiPo batteries, especially for wearable designs, we always use a BMS board for safety. The liability is not worth the savings to us. The last thing you want to do is have one of your designs injure someone. All batteries, especially LiPo batteries, store a lot of energy, and if all of that energy is released too quickly, it can physically damage its surroundings or even harm a user. The energy high density in LiPo batteries demands a designer’s respect.

See Also : 

TOP WEARABLE TECHNOLOGY STARTUPS

Read Also

Wearables And Cybersecurity

Wearables And Cybersecurity

Arlette Hart, Senior Technologist for Cybersecurity, Leidos
Wearable Technology - The Future is Now

Wearable Technology - The Future is Now

Jim Lefevere, International Business Leader, Non-Insulin Therapy Solutions , Roche Diabetes Care
Stay Nimble and Be Prepared to Pivot

Stay Nimble and Be Prepared to Pivot

Mark Mastalir, Co-CEO, Halo Neuroscience

Weekly Brief